Vermont CDL DMV Endorsement Bus 2
Take 10 practice tests for CDL is the best way to prepare for your Vermont DMV exam is by taking our free practice tests. The following question are from real Vermont DMV practice test. More than 95% people pass a DMV exam when practice at DMV Practice Test.
- 0Correct
- 0Incorrect
Ouch! While you were on a roll there for a few questions, you didn’t pass this time. But I know this test, and I think you’ll pass next time. Really.
When checking your vehicle's pedals during a pre-trip inspection, you should ensure that there is nothing under or around the pedals that will obstruct their use. Make sure the pedals are in proper working condition and that the surfaces of the pedals are grooved, if applicable.
The examiner will score the number of times your vehicle touches or crosses an exercise boundary line. Each encroachment will count as an error, resulting in points against your skills test score.
During the on-road driving test, do not stop, change gears, pass another vehicle, or change lanes while any part of your vehicle is in a railroad crossing.
Do not shift gears while crossing railroad tracks. Your vehicle could stall and get stuck in the crossing.
Railroad crossings with control devices to regulate traffic are known as active crossings. Control devices may include regulators such as flashing red lights, warning bells, and gates. Drivers are required by law to follow instructions given by control devices.
Properly adjusted crossover mirrors on a school bus should allow the driver to see the entire area in front of the bus, from the front bumper at ground level to a point where direct vision is possible. The mirrors should also display the right and left front tires touching the ground, as well as the area from the front of the bus to the service door.
When inspecting a trailer coupling, you should make sure the fifth wheel locking jaws are closed around the shank of the kingpin, not the head of the kingpin.
School bus drivers should approach stops slowly and cautiously.
At a stop, a school bus should be stopped with the front bumper at least 10 feet away from the students. This forces the students to walk toward the bus, allowing the driver to keep an eye on their movements.
On a school bus, the overhead inside rearview mirror is mounted directly above the windshield on the driver’s side of the bus. This mirror should be used to monitor students inside the bus.
If a school bus is on fire, or if there is a threat of fire, it is mandatory for a bus driver to evacuate the students from the bus.
A pre-trip inspection should be completed in the same way before every drive. Consistency will help you learn all of the proper steps and decrease the likelihood that you will forget to check something.
If you are asked to complete an offset back/right parking maneuver, you should first pull straight forward, then back up to the right. Your vehicle must be parked completely within the boundaries of the parking space.
When asked to make a lane change during the on-road driving test, you should make the proper traffic checks, use your turn signal, and smoothly change lanes when it is safe to do so.
Students should not occupy the back row of a school bus unless the bus is full. The closer to the front of a bus that students are seated, the safer they will be in the event of a rear-end collision. Students with special needs should sit near the driver.
The doors of a school bus must be kept closed any time the bus is moving, except when it is crossing railroad tracks.
Most commercial vehicles manufactured after 1998 or 1999 are required to be equipped with Anti-Lock Braking Systems (ABS). Many older buses are also equipped with ABS.
In a school bus, the overhead rearview mirror is mounted directly above the windshield on the driver’s side.
If a school bus becomes stalled or trapped on railroad tracks, the driver should get everyone out of the bus and off of the tracks immediately. The driver and students should move away from the tracks at an angle and in the direction of any oncoming train.
You may be asked to complete a conventional parallel parking maneuver into a parking space that is to the right of your vehicle. You should drive past the parking space before backing into it while bringing the rear of your vehicle as close to the rear of the space as possible. Your vehicle should be completely within the boundaries of the space.
Try more CDL Vermont Practice Test
- 0Incorrect (4 allowed to pass)
- 0Correct