New York CDL DMV Air Brakes 2

Before driving a vehicle with a dual air brake system, allow time for the air compressor to build up pressure of at least 100 psi in both the primary and secondary systems.

A dolly equipped with an Anti-Lock Braking System (ABS) is required to have a yellow malfunction lamp located on its left side.

In an air brake system, a low air pressure warning signal must come on if air pressure in the tanks falls below 60 psi. This warning signal may come in the form of a light, a buzzer, or a wig wag.

In newer vehicles with air brakes, the parking brakes are controlled by a diamond-shaped yellow knob. Pull the knob out to activate the parking brakes and push it in to release them.

Check each slack adjuster after parking on level ground, setting wheel chocks, and disengaging the parking brake. Pull the slack adjusters to make sure they do not move more than about one inch from where the push rod is attached. If they move more than one inch, they may be out of adjustment and will need to be fixed.

If you are unsure if a trailer is equipped with an Anti-Lock Braking System (ABS), look under the vehicle for the electronic control unit and wheel speed sensor wires coming from the back of the brakes.

In an air brake system, the application pressure gauge shows how much air pressure is being applied to the brakes. Not all vehicles with an air brake system have this gauge.

The stab braking method for emergency stops involves fully applying the brakes until they lock up. The brakes are then released until the wheels start rolling, then the process is repeated.

Before driving a vehicle with a dual air brake system, you should wait for the air compressor to build up at least 100 psi in both the primary and secondary systems.

It is important to know the maximum air loss rate that is safe for your specific vehicle. A triple combination should have a leakage rate no higher than 6 psi in a minute during an applied leakage test.

Pressing and releasing the brake pedal unnecessarily can let air out faster than the compressor can replace it, reducing the available air pressure. If the air pressure in an air brake system gets too low, the brakes will no longer work.

Because air takes time to flow through the air lines to the brakes, air brakes cannot begin working instantly. There is often a brake lag of at least one-half of a second between the moment the brake pedal is pressed and the moment the brakes begin to work.

Truck tractors with air brakes that were manufactured on or after March 1, 1997 are required to be equipped with Anti-Lock Braking Systems (ABS). ABS is required in any other type of vehicle with air brakes that was manufactured on or after March 1, 1998.

A low air pressure warning signal is required in vehicles with air brakes. The warning light is usually red and may be accompanied by a buzzer.

Both systems in a dual air brake system share a single air compressor. If the air compressor is damaged, neither system will be able to operate properly.

Compressed air in an air brake system usually contains a certain amount of water and compressor oil. The water and oil can damage the brakes if left to accumulate in the system. Tanks must be drained regularly to remove this build-up.

The function of an Anti-Lock Braking System (ABS) is to prevent the vehicle's wheels from locking up from hard brake application.

Tractors, trucks, and buses with Anti-Lock Braking Systems (ABS) have yellow malfunction lamps located on their instrument panels. Trailers have yellow ABS malfunction lamps on their left side, either on the front or rear corner.

Vehicles with Anti-Lock Braking Systems (ABS) have yellow malfunction lamps.

Before driving a vehicle with a dual air system, allow time for the air compressor to build up a minimum pressure of 100 psi in both the primary and secondary systems.

A dual air brake system has two separate air brake systems that use a single set of brake controls. One system typically operates the regular brakes on the rear axle or axles. The other system operates the regular brakes on the front axle.

Air brake system tanks must contain drain valves. These valves are used to drain accumulated oil and water from the tanks and may be either manually or automatically operated.

Using the brakes excessively will cause them to overheat, making them less effective. This is referred to as "fading."

The service brake system applies and releases the brakes when a driver presses the brake pedal while driving normally.

When a brake pedal is pressed and the S-cam is turned, the S-cam presses the brake shoes against the inside of the brake drum. This causes friction and will cause the vehicle to slow.