New Hampshire CDL DMV Air Brakes 1

Before driving a vehicle with a dual air brake system, allow time for the compressor to build up pressure to at least 100 psi in both systems.

In a tractor-trailer combination, if the tractor is equipped with an Anti-Lock Braking System (ABS) but the trailer is not, the ABS will still improve the driver's steering control. The driver should keep an eye on the trailer and let up on the brakes if the trailer begins to swing out.

It is essential that your low pressure warning light functions properly. After allowing the system to charge, you can test the warning signal by rapidly applying and releasing the brake pedal. This will release air from the braking system and the warning signal should come on when pressure drops to a dangerous level.

The stab braking method for emergency stops involves fully applying the brakes until they lock up. The brakes are then released until the wheels start rolling, and then the process is repeated.

Truck tractors with air brakes that were manufactured on or after March 1, 1997 are required to be equipped with Anti-Lock Braking Systems (ABS). ABS is required in any other type of vehicle with air brakes that was manufactured on or after March 1, 1998.

In an air brake system, the air compressor governor controls when the air compressor pumps air into the air storage tanks.

When a brake pedal is pressed and the S-cam is turned, the S-cam presses the brake shoes against the inside of the brake drum. This causes friction and will cause the vehicle to slow.

In an air brake system, the application pressure gauge shows how much air pressure is being applied to the brakes. Not all vehicles with an air brake system have this gauge.

All trucks, truck tractors, and buses must be equipped with emergency brakes and parking brakes. These brakes must be held by mechanical force.

Air brakes function through the use of compressed air.

A modulating control valve allows a driver to gradually apply spring brakes. In equipped vehicles, the valve is controlled by a lever located on the dashboard.

After the brake pedal is pushed down in a vehicle with air brakes, it takes a half-second or more for air to flow through the lines and make the brakes work. This contrasts with hydraulic brakes used in cars and light and medium trucks, which instantly begin working when the pedal is pushed.

A dolly equipped with an Anti-Lock Braking System (ABS) is required to have a yellow malfunction lamp located on its left side.

Because air takes time to flow through the air lines to the brakes, air brakes cannot begin working instantly. There is often a brake lag of at least one-half of a second between the moment the brake pedal is pressed and the moment the brakes begin to work. On vehicles with hydraulic brakes, the brakes work instantly when the pedal is pressed.

While driving downhill, you should hold down the brake pedal until your vehicle reaches a speed 5 mph below your safe speed, then release the brake pedal. Repeat this process.

To make a normal stop in a vehicle that is equipped with air brakes, you should simply press the brake pedal down.

Brakes are particularly prone to getting out out adjustment if they are hot. Use proper braking techniques to avoid letting your brakes overheat.

Most heavy-duty vehicles use dual air brake systems, in which there are two separate braking systems operated by a single set of controls. Each system operates the brakes on different axles.

An air compressor governor will stop the compressor from pumping air once the air tanks are at an air pressure level around 125 psi. This air pressure level is referred to as the "cut-out" level.

In general, you should always use the parking brake when parking your vehicle. However, you should not apply the parking brake if your brakes are very hot or if your brakes are wet and temperatures are below freezing.

A dual air brake system has two separate air brake systems that use a single set of brake controls. One system typically operates the regular brakes on the rear axle or axles. The other system operates the regular brakes on the front axle.

The parking brake should be applied every time you park your vehicle.

A vehicle with air brakes must be equipped with a low air pressure warning signal. If the warning signal goes off while a vehicle is being driven, the driver should bring the vehicle to a complete stop and have the system repaired.

When inspecting a vehicle with a dual air brake system, you should wait for air pressure to build from 85 to 100 psi in both the primary and secondary systems. This should take about 45 seconds.

On a downgrade, the braking effect of the engine should be your primary method of controlling speed. Shift down to a lower gear before starting down the hill and save the brakes for additional slowing or stopping that may be required by road or traffic conditions.