Missouri CDL DMV Air Brakes 1

The safety valve protects air tanks and the rest of an air brake system from accumulating too much air pressure. The safety valve is usually set to open at 150 psi.

When inspecting a vehicle with a dual air brake system, you should wait for air pressure to build from 85 to 100 psi in both the primary and secondary systems. This should take about 45 seconds.

A dual air brake system is made up of two separate air brake systems. The systems share a single set of brake controls, but each has its own air tanks, hoses, and lines. One system typically operates the regular brakes on the rear axle or axles while the other system operates the regular brakes on the front axle.

Some air brake systems include an evaporator that introduces alcohol into the system. The alcohol can help prevent ice from forming within the system.

While driving, spring brakes are generally held in place by air pressure. If the air pressure gets low enough, the springs will activate the brakes.

The purpose of an Anti-Lock Braking System (ABS) is to prevent wheel lockup while brakes are being applied.

Components of an air brake system include an air compressor, an air compressor governor, air storage tanks, air tank drains, an alcohol evaporator, a safety valve, a brake pedal, foundation brakes, supply pressure gauges, an application pressure gauge, a low air pressure warning signal, a stop light switch, a front brake limiting valve (on some older vehicles), spring brakes, and parking brake controls.

The air storage tanks in an air brake system store compressed air to be used for braking. They hold enough air for the brakes to still be used several times if the compressor stops working.

When performing a static leakage test on a single vehicle with air brakes, the leakage rate should be no more than 2 psi in a minute. If the air leaks from the air brake system at a quicker rate, the vehicle should not be driven because something likely needs to be repaired.

It is important to know the maximum air loss rate that is safe for your specific vehicle. A triple combination should have a leakage rate no higher than 6 psi in a minute during an applied leakage test.

A visual low pressure warning signal should activate before air pressure drops to a level between 55 and 75 psi. This signal could be a light, a buzzer, or a wig wag.

Before driving a vehicle with air brakes, you should ensure that the spring brakes come on automatically when air tank pressure falls to a level between 20 and 45 psi. You can do this by chocking the wheels and releasing air from the braking system by stepping on and off the brake pedal. Once the pressure levels drop to an unsafe level, the parking brake valve should pop out and spring brakes should come on.

In an air brake system, the air compressor pumps air into the air storage tanks. The air compressor is controlled by the air compressor governor.

When parking on a level surface, you should use wheel chocks. If the vehicle is not equipped with spring brakes, this is essential to prevent the trailer from moving.

Some older vehicles have front brake limiting valves with "normal" and "slippery" settings. Setting a brake limiting valve to "slippery" reduces the vehicle's stopping power, so a driver should make sure the valve is in its "normal" position. Front wheel braking has proven to be effective in all driving conditions.

Air brakes function through the use of compressed air.

If you need to make an emergency stop, you can use either the controlled braking method or the stab braking method. It's important to brake in a way that keeps your vehicle in a straight line but will still allow you to turn if necessary.

In an air brake system, air tank drains are used to remove water and compressor oil from the air tanks. When operating a drain, be sure to drain the tank completely.

In a vehicle with dual parking control valves, there is a separate air tank that can be used to temporarily release the spring brakes if they have been activated due to low air pressure. Pushing in the proper control will release the spring brakes for a short period of time, allowing the driver to move the vehicle in an emergency.

On long and/or steep downgrades, you should primarily use engine braking to control the speed of your vehicle. Use your brakes only as a supplement to this effect.

The safety relief valve in an air brake system releases air if necessary to prevent pressure in the system from becoming too high. If the valve starts releasing air, there is something wrong. Have a mechanic fix the problem.

Before a trip, you should check each slack adjuster after parking, setting wheel chocks, and disengaging the parking brake. Pull the slack adjusters to make sure that they do not move more than about one inch from where the push rod is attached. If they move more than one inch, they may be out of adjustment and will need to be fixed.

If the low pressure warning signal activates while you are driving, it is important that you safely exit the roadway as soon as possible and park your vehicle. If the air pressure gets too low, the brakes will no longer work well enough for you to stop safely.

Vehicles with air brakes are required to be equipped with a low pressure warning device. A wig wag is a type of low air pressure warning device. This device drops a mechanical arm into the driver's view if the pressure in the tanks drops to a level between 55 and 75 psi.

If you have an Anti-Lock Braking System (ABS) equipped on only the tractor, only the trailer, or only one axle, you will still have more control over the vehicle when braking than you would without ABS. You should brake normally.