Kentucky CDL DMV Air Brakes 1

Vehicles with air brakes are required to be equipped with a low pressure warning device. A wig wag is a type of low air pressure warning device. This device drops a mechanical arm into the driver's view if the pressure in the tanks drops to a level between 55 and 75 psi.

In a vehicle with air brakes, the brake lights are activated when the brake pedal is pushed and air pressure moves an electric switch. With the application of air pressure, the switch will then turn on the brake lights.

Some older vehicles have front brake limiting valves with "normal" and "slippery" settings. Setting a brake limiting valve to "slippery" reduces the vehicle's stopping power, so a driver should make sure the valve is in its "normal" position. Front wheel braking has proven to be effective in all driving conditions.

Brakes out of adjustment will fade before those that are properly adjusted. Brake adjustment must be checked frequently to help prevent brake issues.

Anti-Lock Braking Systems (ABS) are compatible with air brakes and help a driver maintain control of their vehicle by preventing wheel lockup.

Air brakes are really three different braking systems: the service brake, the parking brake, and the emergency brake. Emergency and parking brakes are applied with mechanical force.

All trucks, truck tractors, and buses must be equipped with emergency brakes and parking brakes. Because air pressure can eventually leak away, emergency and parking brakes should be held on by mechanical force.

An air brake system has a safety relief valve, which releases air from the tanks if the pressure gets too high. If the valve must operate, something in the system is wrong and should be addressed by a mechanic.

Both systems in a dual air brake systems share a single air compressor. If the air compressor is damaged, neither system will be able to operate properly.

If brakes are overused, they can become too hot. This overheating causes them to fade, making them less effective at slowing the vehicle.

Brakes are particularly prone to getting out of adjustment if they are hot. Be sure to routinely check the adjustment of your brakes. For a vehicle to be safely controlled, all brakes must be properly functioning and adjusted.

All trucks, truck tractors, and buses must be equipped with emergency brakes and parking brakes.

Components of an air brake system include an air compressor, an air compressor governor, air storage tanks, air tank drains, an alcohol evaporator, a safety valve, a brake pedal, foundation brakes, supply pressure gauges, an application pressure gauge, a low air pressure warning signal, a stop light switch, a front brake limiting valve (on some older vehicles), spring brakes, and parking brake controls.

The safety valve protects air tanks and the rest of an air brake system from accumulating too much air pressure. The safety valve is usually set to open at 150 psi.

In situations where a driver cannot use a parking brake, wheel chocks can be used to hold a parked vehicle in place on a level surface.

In newer vehicles with air brakes, the parking brake is controlled by a yellow, diamond-shaped knob. The driver should pull the knob outward to apply the parking brakes and push the knob inward to release them.

In an air brake system, the air tanks must be periodically drained to remove accumulations of water and compressor oil. If water is not removed, it could freeze in cold weather and cause brake failure.

When parking on a level surface, you should use wheel chocks. If the vehicle is not equipped with spring brakes, this is essential to prevent the trailer from moving.

When performing a static leakage test on a double combination vehicle with air brakes, the leakage rate should be no more than 3 psi in one minute. If the air leaks from the air brake system at a quicker rate, the vehicle should not be driven because something likely needs to be repaired.

The air compressor of an air brake system is connected to the engine through gears or a v-belt. The compressor may be air-cooled or cooled by the engine cooling system.

The total stopping distance for vehicles equipped with air brakes is made up of four factors: perception distance, reaction distance, brake lag distance, and braking distance. When braking at a speed of 55 mph while driving on dry pavement, the brake lag can add around 32 feet to the vehicle's total stopping distance.

Many large CMVs are equipped with air brakes. An air braking system uses compressed air to operate.

Vehicles with ABS have yellow malfunction lamps to alert drivers when the braking systems are not working. Be sure you know where the malfunction lamp on your vehicle is before beginning a trip.

Any vehicle with air brakes must be equipped with a low air pressure warning signal.

If used and maintained properly, air brakes are a safe and effective way to stop large, heavy vehicles.