Kansas CDL DMV Knowledge Test Class B 1
Take 4 practice tests for CDL is the best way to prepare for your Kansas DMV exam is by taking our free practice tests. The following question are from real Kansas DMV practice test. More than 95% people pass a DMV exam when practice at DMV Practice Test.
- 0Correct
- 0Incorrect
Ouch! While you were on a roll there for a few questions, you didn’t pass this time. But I know this test, and I think you’ll pass next time. Really.
Operators driving too fast is a major cause of fatal crashes. You must continually adjust your speed to a rate that is safe for road and traffic conditions.
When exiting your vehicle during the basic vehicle control skills test, you must face the vehicle and maintain three points of contact at all times. If your testing vehicle is a bus, you must maintain contact with the handrail. Exiting the vehicle incorrectly may result in automatic failure of the basic control skills test.
Always downshift before beginning to drive downhill. Forcing an automatic transmission into a lower gear at a high speed could damage the transmission and also lead to a loss of ability to engine brake. Drive at a speed that will allow you to control your vehicle without overusing your brakes. When determining a safe speed to drive, you should take into account the steepness of the grade, the length of the grade, the weight of your vehicle, road conditions, and weather conditions.
A large vehicle may need to swing right to make a left turn. If an intersection has two left turn lanes, the driver should choose the righthand land to begin their turn.
When inspecting an enclosed trailer as a part of the vehicle inspection test, check the front area of the trailer for signs of damage, such as cracks, bulges, or holes.
If you are asked to alley dock, you should first pull past the alley and stop your vehicle in a position that is parallel to the outer boundary. From there, you should back your vehicle entirely into the alley parking area. Your vehicle should be parked in a straight position within the boundaries of the parking space.
If you begin to feel drowsy while driving, the only safe response is to safely leave the road and get some sleep. Using artificial stimulants can be dangerous because they may cause extreme fatigue when they begin to wear off.
Railroad crossings that are not controlled by any type of traffic control device are known as passive crossings. The decision to proceed across tracks at a passive crossing is entirely up to the driver.
It is important to observe other drivers' behaviors and identify clues that indicate when person could be driving impaired. Drivers who have had too much to drink, are sleepy, are on drugs, or are ill can present hazards to other drivers. A person driving with their window open in cold weather may be impaired.
Gross Vehicle Weight (GVW) is defined as the total weight of a single vehicle in addition to its load.
Maneuvers that may be included in the basic vehicle control skills test include straight line backing, offset back/right parking, offset back/left parking, driver side parallel parking, conventional parallel parking, and alley docking.
Gross Vehicle Weight Rating (GVWR) is the weight specified by the manufacturer as the maximum weight of a single vehicle and its load.
To reduce the risk of distraction, do not engage in complex or emotionally intense conversations while driving. Pre-programming radio stations before your trip and avoiding eating, drinking, or smoking while at the wheel can also help you avoid becoming distracted while driving. Remember that mental distractions that take your attention away from the task of driving can be just as dangerous as physical distractions.
Check your tires regularly when looking in your mirrors. This helps ensure that you will notice a tire fire, if one should happen. Tire fires may occur when a tire is under-inflated, if dual tires are touching, or if the tires are otherwise overheated.
It is both illegal and dangerous to send or read text messages while driving in the state of Kansas.
A low air pressure warning signal is required in vehicles with air brakes. The warning light is usually red and may be accompanied by a buzzer.
During the on-road driving test, you must drive in a safe and responsible manner; wear your safety belt; obey all traffic signs, signals, and laws; and complete the test without any accidents or moving violations.
On a downgrade, the braking effect of the engine should be your primary method of controlling speed. Shift down to a lower gear before starting down the hill and save the brakes for additional slowing or stopping that may be required by road or traffic conditions.
Fatigue and lack of alertness are major hazards when driving at night. Most people are the least alert at night, especially after midnight.
If you use a helper while backing your vehicle, they should stand near the back of the vehicle in a place where they are visible to you. Before backing, work out a set of hand signals that both you and your helper understand. Agree on a signal for "stop."
A tire load rating is the maximum safe weight that can be carried by a tire at a specified pressure. This number is stated on the side of each tire.
Backing can be dangerous, so avoid doing it whenever you can. If possible, park in such a way that allows you to pull forward to exit your parking space.
Increasing your vehicle's speed will increase your vehicle's striking power and braking distance. Doubling your vehicle's speed from 20 to 40 mph will multiply its braking distance by four.
Because they are exposed to less sunlight, shaded patches of road will stay cooler longer than other areas of the road. Due to the lack of direct sunlight, shady areas can remain icy and slippery after ice on other areas of the road has melted.
If confronted by an aggressive driver, it is most important to get out of their way. Avoid making eye contact and do not gesture at them. Report them to the appropriate authorities once you can safely do so.
Commercial vehicles should always carry the proper emergency equipment. Be sure your vehicle is equipped with at least one fire extinguisher; spare electrical fuses, unless the vehicle is equipped with circuit breakers; and warning devices for parked vehicles, such as warning triangles, fuses, or liquid burning flares.
In general, if you operate a commercial vehicle in interstate commerce, it must be registered under the International Registration Plan (IRP) and International Fuel Tax Agreement (IFTA). These programs collect and distribute vehicle registration fees and fuel taxes based on what jurisdictions you drive in and for how long. Mileage and fuel records supporting IFTA quarterly fuel tax returns must be retained by carriers for four years.
If your hydraulic bakes fail, shifting into a lower gear can help slow your vehicle down.
When parking as a part of the stop/start maneuver during the on-road driving skills test, you must apply the parking brake. The gears should be shifted into neutral or park. You must be parked parallel to the curb and should not be blocking any driveways or intersections.
When exiting your vehicle during the basic vehicle control skills test, you must face the vehicle and maintain three points of contact at all times. If your testing vehicle is a bus, you must maintain contact with the handrail. Exiting the vehicle incorrectly may result in automatic failure of the basic control skills test.
The parking brake in a vehicle with air brakes should be used every time the vehicle is parked.
If you need to make an emergency stop, you can use either the controlled braking method or the stab braking method. It's important to brake in a way that keeps your vehicle traveling in a straight line while still allowing you to turn, if necessary.
In a newer vehicle with air brakes, the parking brake is controlled by a diamond-shaped yellow knob. The knob is pulled out to apply the parking brakes and pushed in to release them.
If a federal or state inspector judges a CMV to be unsafe, they may put it out-of-service until it is fixed.
A one-way check valve is required to be between an air compressor and the first main reservoir. This valve prevents air from escaping the system if the air compressor develops a leak.
Try more CDL Kansas Practice Test
- 0Incorrect (7 allowed to pass)
- 0Correct