Idaho CDL DMV Endorsement Hazmat 2
Take 10 practice tests for CDL is the best way to prepare for your Idaho DMV exam is by taking our free practice tests. The following question are from real Idaho DMV practice test. More than 95% people pass a DMV exam when practice at DMV Practice Test.
- 0Correct
- 0Incorrect
Ouch! While you were on a roll there for a few questions, you didn’t pass this time. But I know this test, and I think you’ll pass next time. Really.
A pre-trip inspection should be completed in the same way before every drive. Consistency will help you learn all of the proper steps and decrease the likelihood that you will forget to check something.
If the words "Inhalation Hazard" are on a package or its shipping paper, you must display the proper inhalation hazard placards, as well as any other necessary placards. This applies regardless of the amount of materials being carried.
A hazardous material will be placed into one of nine classes to explain the type of risks associated with the material.
If you are asked to complete an offset back/left parking maneuver, you should first pull straight forward, then back up to the left. Your vehicle must be parked completely within the boundaries of the parking space.
The National Response Center must be notified of any incident that results in death; hospitalization; $50,000 or more in estimated property damage; an evacuation of the general public or closure of a major transportation route/facility for more then one hour; fire, breakage, spillage, or suspected contamination involving radiation, bacteria, or toxins. Additionally, if the carrier judges the situation to be so serious that it should be reported, it should be reported.
Shippers of certain kinds of hazardous materials are required to display diamond-shaped warning signs, known as placards, on any transporting vehicles. Shippers are required to provide applicable placards, labels, shipping papers, and emergency response information.
When required, hazardous materials placards must be placed on the front, rear, and both sides of a vehicle.
A driver uses a look when they open their door, leave their seated position, and walk to the back of the vehicle to check its position. During the straight line backing exercise, a driver may not exceed one look. During any other exercise, a driver may not exceed two looks.
If your vehicle breaks down while you are transporting explosives and you need to use warning signals, use reflective triangles or red electric lights. Never use burning signals, such as flares or fuses, when transporting explosives.
In general, vehicles carrying hazardous materials are required to display diamond-shaped warning signs on all four sides. These warning signs are called "placards."
Among other information, shipping papers must include a description of the specific hazardous materials being transported.
If you discover a cargo leak while transporting hazardous materials, use the shipping papers, label, or package location to identify which materials are involved. Do not try to touch or smell the leaking materials to determine what they are because doing so could result in injury or death.
Diamond-shaped signs called placards are placed on bulk packages and on the outside of vehicles to warn drivers and others of the presence of hazardous materials. It is the responsibility of the shipper to place the placards, and it is the responsibility of the driver to verify that the correct placards have been placed.
If you are transporting hazardous waste, you must carry with you a Uniform Hazardous Waste Manifest. The manifest must be signed by hand.
Maneuvers that may be included in the basic vehicle control skills test include straight line backing, offset back/right parking, offset back/left parking, driver side parallel parking, conventional parallel parking, and alley docking.
The power unit of a placarded vehicle must be equipped with a fire extinguisher with an Underwriters Laboratories (UL) rating of 10 B:C or more.
Hazardous materials placards must be placed on a vehicle at least three inches away from any other markings and must positioned so that the words or numbers are level and read from left to right.
Parts of a vehicle that have been exposed to corrosive liquids must be thoroughly washed with water.
Keep liquid discharge valves on a compressed gas tank closed except when loading and unloading.
If the words "Inhalation Hazard" appear on the shipping paper or package, you must display the "Poison Inhalation Hazard" or "Poison Gas" placards, as appropriate.
On a compressed gas tank, liquid discharge valves must always be kept closed, except during loading and unloading.
During the on-road driving test, the examiner will be score you on specific driving maneuvers as well as on your general driving behavior. You must drive in a safe and responsible manner; obey all traffic signs, signals, and laws; and not cause an accident or commit a moving violation.
If your on-road driving test route does not include a railroad crossing, you may be asked to explain and demonstrate the proper railroad crossing procedures to the examiner at a simulated location.
When asked to make a turn during the on-road driving test, you must check traffic in all directions and use your turn signal.
In general, vehicles carrying hazardous materials are required to display diamond-shaped warning signs on all four sides. These warning signs are called "placards."
If you are involved in an accident while carrying hazardous materials, it is your responsibility as the driver to keep people away from the scene; limit the spread of material if you can safely do so; inform emergency response personnel of the dangers posed by the materials; and provide emergency personnel with the shipping papers and emergency response information. Unless you have protective equipment and the necessary training, do not try to fight hazardous materials fires yourself.
The shipper of hazardous materials is responsible for packaging, marking, and labeling the materials properly. It is a good idea for the driver to ensure the materials are properly labeled.
If you are asked to alley dock, you should first pull past the alley and stop your vehicle in a position that is parallel to the outer boundary. From there, you should back your vehicle entirely into the alley parking area. Your vehicle should be parked in a straight position within the boundaries of the parking space.
If you are asked to complete an offset back/right parking maneuver, you should first pull straight forward, then back up to the right. Your vehicle must be parked completely within the boundaries of the parking space.
When asked to make a lane change during the on-road driving test, you should make the proper traffic checks, use your turn signal, and smoothly change lanes when it is safe to do so.
Try more CDL Idaho Practice Test
- 0Incorrect (6 allowed to pass)
- 0Correct