Delaware CDL DMV Air Brakes 2

Vehicles with air brakes are required to be equipped with a low pressure warning device. A wig wag is a type of low air pressure warning device. This device drops a mechanical arm into the driver's view if the pressure in the tanks drops to a level between 55 and 75 psi.

The service brake system applies and releases the brakes when a driver presses the brake pedal while driving normally.

A dual air brake system has two separate air brake systems that use a single set of brake controls. One system typically operates the regular brakes on the rear axle or axles. The other system operates the regular brakes on the front axle.

The safety relief valve in an air brake system releases air if necessary to prevent pressure in the system from becoming too high. If the valve starts releasing air, there is something wrong. Have a mechanic fix the problem.

All trucks, truck tractors, and buses must be equipped with emergency brakes and parking brakes. Because air pressure can eventually leak away, emergency and parking brakes should be held on by mechanical force.

Anti-Lock Braking System (ABS) malfunction lamps are usually yellow. Even if the ABS isn't working properly, a driver will still have access to the vehicle's usual braking functions.

Most heavy-duty vehicles use dual air brake systems, in which there are two separate braking systems operated by a single set of controls. Each system operates the brakes on different axles.

When performing a static leakage test on a triple combination vehicle with air brakes, the leakage rate should be no more than 5 psi in one minute. If air leaks from the air brake system at a quicker rate, the vehicle should not be driven because something likely needs to be repaired.

In newer vehicles with air brakes, the parking brakes are controlled by a diamond-shaped yellow knob. Pull the knob out to activate the parking brakes and push it in to release them.

In an air brake system, the air tanks must be periodically drained to remove accumulations of water and compressor oil. If water is not removed, it could freeze in cold weather and cause brake failure.

Before driving a vehicle with a dual air brake system, you should wait for the air compressor to build up at least 100 psi in both the primary and secondary systems.

In an air brake system, pressing and releasing the brake pedal unnecessarily can release air from the braking system faster than the compressor can replace it.

When performing a static leakage test on a single vehicle with air brakes, the leakage rate should be no more than 2 psi in a minute. If the air leaks from the air brake system at a quicker rate, the vehicle should not be driven because something likely needs to be repaired.

In an air brake system, the application pressure gauge shows how much air pressure is being applied to the brakes. Not all vehicles with an air brake system have this gauge.

The purpose of an Anti-Lock Braking System (ABS) is to prevent a vehicle's wheels from locking up when the driver brakes hard on a slippery surface.

Some air brake systems include an evaporator that introduces alcohol into the system. The alcohol can help prevent ice from forming within the system.

For safety, most heavy-duty vehicles are equipped with dual air brake systems.

A vehicle that is equipped with air brakes must also be equipped with a supply pressure gauge. This gauge tells the driver how much air pressure is in each of the vehicle's air tanks.

Never apply the brake pedal if your spring breaks are activated. Brakes can be damaged if they are subject to both springs and air pressure.

It is important to know the maximum air loss rate that is safe for your specific vehicle. A double combination vehicle should have a leakage rate no higher than 4 psi in a minute during an applied leakage test.

An air compressor governor will stop the compressor from pumping air once the air tanks are at an air pressure level of 125 psi. This air pressure level is referred to as the "cut-out" level.

In vehicles with air brakes, the parking brake is controlled by a knob. The knob is pulled out to apply the brakes, and pushed in to release them.

The function of an Anti-Lock Braking System (ABS) is to prevent the vehicle's wheels from locking up from hard brake application.

Brake linings should not be loose or soaked with oil or grease. They shouldn't be dangerously thin.

A modulating control valve allows a driver to gradually apply spring brakes. In equipped vehicles, the valve is controlled by a lever located on the dashboard.