Alaska CDL DMV Air Brakes 2
Take 6 practice tests for CDL is the best way to prepare for your Alaska DMV exam is by taking our free practice tests. The following question are from real Alaska DMV practice test. More than 95% people pass a DMV exam when practice at DMV Practice Test.
- 0Correct
- 0Incorrect
Ouch! While you were on a roll there for a few questions, you didn’t pass this time. But I know this test, and I think you’ll pass next time. Really.
When performing a static leakage test on a single vehicle with air brakes, the leakage rate should be no more than 2 psi in a minute. If the air leaks from the air brake system at a quicker rate, the vehicle should not be driven because something likely needs to be repaired.
In an air brake system, the air compressor governor controls when the air compressor pumps air into the air storage tanks.
If a vehicle is equipped, an application pressure gauge shows how much air pressure is being applied to the brakes. This gauge can help a driver identify if their brakes are beginning to fade.
In an air brake system, the air tanks must be periodically drained to remove accumulations of water and compressor oil. If water is not removed, it could freeze in cold weather and cause brake failure.
An alcohol evaporator can help prevent ice from building up in an air brake system. In cold weather, the evaporator should be checked and refilled every day.
Foundation brakes are used on each wheel of a CMV. The most common type of foundation brake is the s-cam drum brake.
An Anti-Lock Braking System (ABS) helps to provide additional control during hard braking, but does not necessarily shorten a vehicle's stopping distance.
Before a trip, you should check each slack adjuster after parking, setting wheel chocks, and disengaging the parking brake. Pull the slack adjusters to make sure that they do not move more than about one inch from where the push rod is attached. If they move more than one inch, they may be out of adjustment and will need to be fixed.
Pressing and releasing the brake pedal unnecessarily can let air out of the braking system faster than the compressor can replace it. Air brakes may cease to work effectively if the pressure becomes too low.
Brakes are particularly prone to getting out of adjustment if they are hot. Be sure to routinely check the adjustment of your brakes. For a vehicle to be safely controlled, all brakes must be properly functioning and adjusted.
In an air brake system, air tank drains are used to remove water and compressor oil from the air tanks. When operating a drain, be sure to drain the tank completely.
An air brake system has a safety relief valve, which releases air from the tanks if the pressure gets too high. If the valve must operate, something in the system is wrong and should be addressed by a mechanic.
The low air pressure warning signal must activate before the air supply pressure drops below 55 psi in the air tank. If the warning signal does not turn on when being tested during an inspection, the vehicle is not safe to drive.
An air compressor governor will stop the compressor from pumping air once the air tanks are at an air pressure level around 125 psi. This air pressure level is referred to as the "cut-out" level.
Vehicles equipped with Anti-Lock Braking Systems (ABS) have yellow malfunction lights to indicate issues in the braking system.
An air brake system has a safety relief valve, which releases air from the tanks if the pressure gets too high. If the valve must operate, something in the system is wrong and should be addressed by a mechanic.
Anti-Lock Braking System (ABS) malfunction lamps are usually yellow. Even if the ABS isn't working properly, a driver will still have access to the vehicle's usual braking functions.
Most newer heavy-duty vehicles use dual air brake systems. A dual air brake system has two separate air brake systems which use a single set of brake controls.
Never push down the brake pedal while the spring brakes are activated. The combined force of springs and air pressure could damage the brakes.
In an air brake system, the air storage tanks hold compressed air to be used by the brakes. The number and size of air tanks varies among vehicles.
The total stopping distance for vehicles equipped with air brakes is made up of four factors: perception distance, reaction distance, brake lag distance, and braking distance. When braking at a speed of 55 mph while driving on dry pavement, the brake lag can add around 32 feet to the vehicle's total stopping distance.
Air brakes are really three different braking systems: the service brake, the parking brake, and the emergency brake. Emergency and parking brakes are applied with mechanical force.
Front wheel braking is effective under all road conditions. It is unlikely that you will experience a front wheel skid, even on ice.
On vehicles with Anti-Lock Braking Systems (ABS), yellow malfunction lamps alert the driver to ABS malfunction.
Before driving a vehicle with a dual air brake system, allow time for the air compressor to build up a minimum of 100 psi pressure in both the primary and secondary systems. Watch the air pressure gauges to monitor the pressure levels.
Try more CDL Alaska Practice Test
- 0Incorrect (5 allowed to pass)
- 0Correct